電壓擊穿試驗儀全自動

介電強度擊穿電壓試驗儀，擊穿強度試驗儀， 電壓擊穿試驗儀， 絕緣材料擊穿電壓試驗儀，耐電壓擊穿強度試驗儀  介電擊穿強度試驗儀,耐電壓強度試驗儀 電壓擊穿試驗儀全自動

產品名稱：電壓擊穿試驗儀

產品型號：BDJC-50KV

控制方式：PC/EPC可選

電壓擊穿試驗儀全自動滿足標準：

           GB1408-2006 絕緣材料電氣強度試驗方法

          GB/T1695-2005 硫化橡膠工頻電壓擊穿強度和耐電壓強度試驗

          GB/T3333 電纜紙工頻電壓擊穿試驗方法

          HG/T 3330絕緣漆漆膜擊穿強度測定法

          GB12656 電容器紙工頻電壓擊穿試驗方法

          ASTM D149 固體電絕緣材料在工業電源頻率下的介電擊穿電壓和介電強度的試驗方法.

主要適用于固體絕緣材料，同時可測得 液體、粉體和不規則物體的擊穿強度。自動整形 測試精度與固體一樣精確。

同時測得工頻交流電壓與直流電壓的擊穿強度和耐壓強度的測試 可設定梯度耐壓的試驗 使梯度時間自由調整。

本儀器由pc控制，通過我公司自主研發的全新智能數字精密嵌入式西門子中央單元cpu系統與上位機軟件控制兩部分來完成，通過pc USB 串口獲得數據傳送數據zui高可高達 3M/S是RS232串口*的 讓上位機與下位機通訊無延遲使升壓速率真正做到勻速、準確，并能夠準確測出漏電電流的數據，電流實時采集。可實時繪制試驗曲線，顯示試驗數據，判斷準確，并可保存，分析，打印，修改試驗數據。并且提取試驗數據分色對比。人性化明顯

試驗軟件簡介：

此設備軟件外觀由專業的美工設計：

人員管理：可添加多人同時使用此軟件 不同人員設定不同密碼 交叉使用互不干擾 （如一人使用可刪除設定密碼  直接進入軟件）

參數管理：高壓保護可選、 耐壓時間可選、 梯度步進可選 、漏電流和過壓可選、靈敏的漏電壓可選、漏電流可選 、升壓速度可自由設定（0-10kv 無極自由）試驗結果可選 異地操作選定 、人機分離選定等等

結果調取：試驗結果保存調取 、人員選定調去 、試驗結果可根據客戶要求操作整理 、支持5次以上彩線對比、自動整取添加試驗數據。

二、電壓擊穿試驗儀技術要求：

01、輸入電壓： 交流 220 V   02、輸出電壓： 交流/直流 0--50 KV ;

03、電器容量： 3KVA         04、高壓分級： 0--50KV

05、升壓速率：0.1-5.0kv     06、試驗方式：

 直流試驗：1、勻速升壓  2、梯度升壓 3、耐壓試驗

 交流試驗：1、勻速升壓 2、梯度升壓 3、耐壓試驗

07、試驗介質：空氣，試驗油   08、安裝靈敏度較高的過電流保護裝置保證試樣擊穿時在0.05S內切斷電源。

09、儀器配備先進的故障報警系統 避免用戶操作故障儀器發生危險。（上位機報警和下位機報警）

10、支持短時間內短路試驗要求。  11、電壓試驗精度： ≤ 1％。

12、試驗電壓連續可調： 0--50 KV。13、電流可采集到mA級 并且實現 實時采集。

14、出具*計量單位校準證書或出具客戶計量單位的證書

15、電源：220v±10%的單相交流電壓和50Hz±1%的頻率

16、電流電壓穩定度：外界電壓波動10% （可選配我司配到電壓保護器 額定波動電壓30%） 17、升壓裝置：采用先進的無觸點原件勻速升壓淘汰前款機械調壓 18、耐壓時間：0-6H保持相對電壓 （軟件設定）  19、擊穿試樣：試樣擊穿點 大小可調一般為1-5mm左右 20、帶有方便拆裝的油浴槽（可根據客戶需要，也可不要油浴槽） 21、機箱材質：優質SUS304 不銹鋼   22、支持人機分離異地操作 開創國內控制機器新篇章 23、控制方式：可選 PC /EPC   

24、通訊方式：采用全國zui*技術無線藍牙控制，支持 232/USB/亞太區域網絡端口。

三、電壓擊穿試驗儀安全保護：

本機具有完善的安全防護措施：

本實驗儀電路保護控制：跳閘后電壓自動回零

1、超壓保護  2、試驗過流保護 3、試驗短路保護4、安全試驗門保護 5、軟件誤操作保護6、零電壓復位保護7、試驗漏點保護  8、獨立接地保護 9、試驗結束放電保護 10、設備故障報警保護

四、電壓擊穿試驗儀設備主要配置

電壓擊穿試驗儀設備標準配置

01 試驗主機 一臺  

02 控制裝置 一套  

03 試驗電極 二套(國標1408.1)  

04 試驗油箱 二只  

05 放電系統 一套  

06 控制系統 一套  

07 數據采集系統 一套  

08 試驗軟件 一套 光盤

09 計算機 一套 品牌  可選 PC/EPC

10 噴墨打印機 一臺 品牌

11 產品使用說明書 一份  

12 計量證書 一份  

13 產品合格證 一份  

使用時的注意事項

1、試驗過程中不能讓無關人員靠近，因本試驗儀器可產生較高的電壓，未經過培訓的人員不能使用該設備。試驗時要有監護人員，不要單人使用。以防萬一發生意外情況。

2、長時間不使用設備，在再使用時，先讓儀器空載加壓一次，即把高壓電極的接線從均壓球上取下。查看計算機試驗界面，看看高壓電壓是否正常。

3、試驗中發生意外情況要及時切斷電源，問題處理后才能繼續試驗。

4、設備安放要平穩，安放的地面要堅固。是水泥地面以免產生共振。

5、該設備在使用中外殼要接保護地線，既設備外殼接大地,以保護操作人員和設備運行的安全。

6、使用完設備后，要關掉系統各部分電源，不準帶電插拔電源線。

7、要按規定的電源電壓接入設備。確保電路接線正確。否則會損壞設備。

8、該儀器需安置在室內，實驗室應整潔、干燥、無腐蝕性介質，非相關人員不要隨意操作。

9、不要讓設備電纜碰到尖邊，以免劃破電纜絕緣；不要讓電纜壓在重物之下，以免壓斷電纜引起火災；不要用電纜拉物體或用電纜捆綁物體，以免拉斷電纜使設備不能正常運轉。

10、不要讓設備碰到水濺，腐蝕性氣體，可燃氣體和可燃物。如果不避免，可能火災。

11、搬動設備時,要切斷設備電源,既要把插頭從插座中拔下。禁止搬動設備時放倒設備或傾斜45°角以上。

12、不要在設備運行時插拔設備的電源插頭。

此設備可分選：

10kv    20kv     50kv     80kv     100kv     150kv     200kv 

Dielectric breakdown voltage tester, dielectric strength tester, voltage tester, insulation breakdown voltage tester, high voltage breakdown strength tester of dielectric breakdown strength tester, dielectric strength tester
Product Name: voltage breakdown testing instrument
Product type: BDJC-50KV
Control: microcomputer control
Meet the standards: GB1408-2006 electrical strength of insulating materials - Test methods
GB/T1695-2005 vulcanized rubber power frequency voltage breakdown strength and dielectric strength test
GB/T3333 cable paper at power frequency voltage breakdown test method
HG/T 3330 insulating varnish films - Determination of electrical breakdown strength
GB12656 capacitor voltage breakdown test method
ASTM D149 of solid electrical insulating materials at commercial power frequencies of dielectric breakdown voltage and dielectric strength test methods.
One, the voltage breakdown testing instrument, the applicable scope and the function
Voltage breakdown testing instrument, mainly applicable to solid insulation materials （ such as: plastic, rubber, thin film, resin, mica, ceramic, glass, insulating paint and other media） in the frequency of the voltage or DC voltage breakdown strength and voltage withstand test.
Voltage breakdown testing instrument, controlled by a computer, through my company independent research and development of new inligent digital integrated circuit and software control system two parts to complete, so that the pressure rate truly uniform, accurate, and can accuray measure the leakage current data.
Real time dynamic drawing test curve, display test data, the judgment is accurate, and can be preserved, analysis, modification, print the test data.
In 1, the instrument in the test process can boost the breakdown process in real time curve drawing, each test boost curve by different color, after testing can be superimposed contrast material testing data repeatability.
2, may at any time to obtain the current and historical test data to view, edit and modify the experimental results.
In 3, during the test can be modified at any time test conditions and storage path and automatic storage test results.
In 4, during the test, may at any time through the software determines the test is effective, convenient screening test results.
In 5, the software set a password, password generation protection, do special person operation, to avoid irrelevant personnel misoperation.
In 6, the test results edited print, convenient and more user-friendly operation.
In 7, of a group of test curve data of the test results are artificially selected.
In 8, the instrument adopts the advanced contactless original uniform pressure, elimination of similar products in the mechanical drive boosting mode.
Two, voltage breakdown testing instrument, technical requirements:
In 01, the input voltage: AC 220 V
In 02, the output voltage: AC 0--50 KV;
DC 0 - 50 KV
03, electrical capacity: 3KVA
In 04, high grade: 0-10KV, 0--50KV,
In 05, 100V/S 200V/S 500 V/S pressure rate: 1000 V/S 2000V/S 5000V/S
（ Note: meet the standard requirements and can be based on user needs to set different pressurization rate ）
06, test method:
DC test: 1, 2, 3 speed boost pressure gradient, pressure test
AC test: 1, 2, 3 speed boost pressure gradient, pressure test
07, voltage breakdown testing instrument, test media: air, test oil
In 08, the installation of high sensitivity over current protection device to ensure that the sample breakdown in 0.05S to cut off the power supply.
09, adopts an inligent integrated circuit speed boost.
10, support a short time short-circuit test requirements.
11, voltage test accuracy:≤ 1%.
In 12, the test voltage is continuous and adjustable: 0--50KV.
13, the current can be collected to level mA.
14, issued by the country one class unit of measurement calibration verification certificate issued or customers designated units of measurement certificate.
15, power: 220V ± 10% single-phase AC voltage and 50Hz±1% frequencies.
16, current and voltage stability: the external power supply voltage fluctuation 10%
Three, security protection
Voltage breakdown testing instrument, circuit protection control:
（ 1） the overpressure protection （ 2） over-current protection （ 3） short circuit protection （ 4） （ 5） software leakage protection misoperation
High voltage input circuit protection control:
（ 1） the total power switch （ 2） regulator reset switch （ 3 ） high voltage disconnecting switch
（ 4） test box door safety switch （ 5） high voltage circuit switch （ 6） leakage protection switch
In four, the main configuration
Standard configuration
Name configuration notes
01 experimental hosts
Control device 02 set
03 the test electrode two （ GB 1408.1 ）
04 test tank two
The 05 discharge system one set
06 control system
07 data collection system
The 08 test a set of Software CD
09 computer of a brand
The 10 one ink-jet printer brand
11 using a manual
A 12 measurement certificate
13 certificate of product a
In four, a voltage breakdown testing instrument, equipment safety instructions:
1, equipment to install a separate protective ground. Grounding protection ground, mostly reduce the sample breakdown when the surrounding the strong electromagnetic interference. Also avoid control computer control.
In 2, the test equipment is provided with a number of circuit protection measures, are: over-current protection, under-voltage protection, leakage protection, short-circuit protection, DC test discharge alarm.
3, grounding requirements: instruments require a separate grounding, grounding of a national standard requirements, metal rods buried at least 1.5 meters below.
In 4, the test equipment is provided with a number of circuit protection measures, are: over-current protection, under-voltage protection, leakage protection, short-circuit protection, DC test discharge alarm.
Five, voltage breakdown testing instrument of conventional models for:
BDJC-10KV
BDJC-20KV
BDJC-30KV
BDJC-50KV
BDJC-100KV
Canton company other insulating materials testing instruments:
BDJC-0-100KV dielectric breakdown testing instrument
BDJC series insulating materials at power frequencies of dielectric breakdown test instrument
BDJC series voltage dielectric strength test apparatus
BDJC series voltage breakdown testing instrument
BDJC series insulating paint film breakdown strength tester
BDJC capacitor voltage breakdown testing instrument
EST-121 volume surface resistivity measuring instrument
GDAT-A dielectric loss tester / dielectric constant test
GDAT-C model dielectric constant dielectric loss tester
BDH leakage resistance tester
BDH-B arc resistance tester
China Inspection and certification services tip and inlectual leader, helped many testing quality inspection units and schools and research units to provide comprehensive one-stop quality solutions.
Pay attention to every detail is Canton company for each customer commitment, and North Canton company has been pursuing the aim of. Beijing North Canton precision instrument equipment limited company